tag:blogger.com,1999:blog-1755726614557851817.comments2023-03-16T08:47:37.333-05:00K9NPXDan Moseshttp://www.blogger.com/profile/13715982336723925525noreply@blogger.comBlogger82125tag:blogger.com,1999:blog-1755726614557851817.post-17134502039269304132021-11-14T21:05:41.608-06:002021-11-14T21:05:41.608-06:00Hmm...don't know what to say...are you followi...Hmm...don't know what to say...are you following the steps correctly and not missing or skipping any of them?<br />Configuration, Expert, SSH Access, logging in with pi-star and your password, setting the transceiver to 433.000 MHz simplex, TS1, TG9, typing sudo pistar-mmdvmcal and pressing Enter, then pressing m and enter, then pressing the space bar to start transmitting? Then going through the rest of the procedure?Bernard Jarihttps://www.blogger.com/profile/16634403493600940996noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-56318355122659338092021-11-14T20:51:05.860-06:002021-11-14T20:51:05.860-06:00TS1 is Time Slot 1
TG9 is Talk Group 9
For running...TS1 is Time Slot 1<br />TG9 is Talk Group 9<br />For running MMDVMCAL<br /><br />TG1 is Talk Group 1<br />CC1 is Color Code 1<br />for running Ber, which I needed to do in order to get my TYT MD9600 to "talk to" the Repeater Builder STM32_DVM, and the RXOFFSET was very high in my estimation or opinion...and for best results, and lowest BER, I needed to use an offset of about 950 which seemed high to me, but with the GD-77 HT, I needed to use an offset of 0, so I needed to decide which offset to use, 950 or 0...unless I could go into the MD9600 and change the transmit a bit, so it could use a 0 offset, or unless I could change the transmit in the GD77 HT, so it could use an offset of 950...but with the IC-4100, and the id-51, both of them worked on D-Star with an offset of either 0 or 950.<br />Bernard Jarihttps://www.blogger.com/profile/16634403493600940996noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-49651145933550930712021-11-14T20:35:58.298-06:002021-11-14T20:35:58.298-06:00"Until the tone comes back" just means w..."Until the tone comes back" just means when you start hearing the tone again.<br />Bernard Jarihttps://www.blogger.com/profile/16634403493600940996noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-78878081323223607842021-11-14T14:02:46.871-06:002021-11-14T14:02:46.871-06:00I can't even hear the tone on my radioI can't even hear the tone on my radio<br />Allotment 5Whttps://www.blogger.com/profile/16163042279638489356noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-48092724576508710432021-10-28T09:50:30.733-05:002021-10-28T09:50:30.733-05:00After a long time, I read a very beautiful and ver...After a long time, I read a very beautiful and very important article that I enjoyed reading. I have found that this article has many important points, I sincerely thank the admin of this website for sharing it. Best <a href="https://accura.ae/labotronics" rel="nofollow">Instruments supply in UAE</a> Services Provider<br />Edward Ortizhttps://www.blogger.com/profile/05553072489301874439noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-74557083627081205472021-07-05T13:05:01.421-05:002021-07-05T13:05:01.421-05:00While the average person might get away with using...While the average person might get away with using a soldering iron here and there for their woodburning projects or to fix the odd component, those who frequently solder need a good soldering station. <a href="https://solderingironguide.com/community" rel="nofollow">Electronics & Soldering Forum – SolderingIronGuide Community – Solderingironguide</a><br /><br />Kevin Nelsonhttps://www.blogger.com/profile/11158105497159863248noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-39741437479407968072021-04-23T14:04:37.146-05:002021-04-23T14:04:37.146-05:00Is there a way to do this for p25?Is there a way to do this for p25?Yarddog KD9GLWhttps://www.blogger.com/profile/12644273076096585931noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-14945559255166712082021-04-05T04:09:12.511-05:002021-04-05T04:09:12.511-05:00Where can I get a charger for this as mine brokeWhere can I get a charger for this as mine brokeAnonymoushttps://www.blogger.com/profile/05546571312276069325noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-232164533151198012021-03-04T09:23:11.375-06:002021-03-04T09:23:11.375-06:00Soldering is not difficult and you can learn how t...Soldering is not difficult and you can learn how to solder in less than an hour just watching a few tutorials and practice assembling soldering DIY kits. <a href="https://solderingironguide.com/brands/power-probe" rel="nofollow">Power Probe</a><br /><br />Francis Smithhttps://www.blogger.com/profile/06494370572012813611noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-2750670447758474802021-02-20T10:42:40.178-06:002021-02-20T10:42:40.178-06:00Where do you get the software to program the radio...Where do you get the software to program the radio? <br />Jayhttps://www.blogger.com/profile/04019707296242476740noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-57576471587964541452021-02-04T20:09:36.840-06:002021-02-04T20:09:36.840-06:00Also, update admin.php, active_reflector_links.php...Also, update admin.php, active_reflector_links.php, settings.php and css_connections.php to exchange the split() with explode()<br /><br />add a "/" to bm_manager.php and bm_links.php after the "include_once $_server['DOCUMENT_ROOT'].' " for each of the for include_once lines at the top of each file.<br />Anonymoushttps://www.blogger.com/profile/00020448021513300590noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-13462947286265917322021-02-04T17:14:11.078-06:002021-02-04T17:14:11.078-06:00Modifying the system.php and the index.php files i...Modifying the system.php and the index.php files in the /var/www/dashboard/mobile directory and exchange the split() with explode() makes everything work in the PHP 7.x version that is installed with pi-star V4.1.4_03 version that I am using.Anonymoushttps://www.blogger.com/profile/00020448021513300590noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-2972474546976911012021-01-23T16:51:00.056-06:002021-01-23T16:51:00.056-06:00Not opening /mobile after installingNot opening /mobile after installingDarkTecknohttps://www.blogger.com/profile/15189330393242332537noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-56146952541026862972021-01-13T17:42:48.808-06:002021-01-13T17:42:48.808-06:00Wow, cool post. I'd like to write like this to...Wow, cool post. I'd like to write like this too - taking time and real hard work to make a great article... but I put things off too much and never seem to get started. Thanks though. <a href="http://www.kybuyshouses.net/" rel="nofollow">duplex buying,</a><br />woodlinkhttps://www.blogger.com/profile/13317326065166106350noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-3214587135006726692021-01-13T05:23:28.029-06:002021-01-13T05:23:28.029-06:00YES, thanks 🙏 finally got my mmvdm woking now!YES, thanks 🙏 finally got my mmvdm woking now!SomeOneSpecialhttps://www.blogger.com/profile/04664766578534204016noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-59792748051212531002020-12-02T22:30:30.493-06:002020-12-02T22:30:30.493-06:00See https://www.youtube.com/watch?v=tMHVzVpCH7U ...See https://www.youtube.com/watch?v=tMHVzVpCH7U (WA9RYO)Badabinghttps://www.blogger.com/profile/09325971231331042718noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-60339923059885786192020-11-12T05:00:33.198-06:002020-11-12T05:00:33.198-06:00As soon as I boot up hot spot. The only page I get...As soon as I boot up hot spot. The only page I get is the expert pi_star log in prompt. Please help.. Been struggling with this for ages. Anonymoushttps://www.blogger.com/profile/13731724736187499031noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-73919915235237848672020-11-12T04:55:59.169-06:002020-11-12T04:55:59.169-06:00I am having trouble connecting to main dash board....I am having trouble connecting to main dash board. But I am loging in to the expert editor page like the one above tried everything from another windows 10 laptop scanned for the ip address tried it. But all I am getting is. Having trouble conectingAnonymoushttps://www.blogger.com/profile/13731724736187499031noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-72539891781030716392020-11-02T04:39:46.960-06:002020-11-02T04:39:46.960-06:00I am entering ip address but all I am getting back...I am entering ip address but all I am getting back is this cannot be reached... Help pleaseAnonymoushttps://www.blogger.com/profile/13731724736187499031noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-58962814821175701402020-11-02T04:31:18.526-06:002020-11-02T04:31:18.526-06:00Going off the mobile subject a bit.. I am new to t...Going off the mobile subject a bit.. I am new to this. Can someone tell me what command I put in to pi _star for home use I have logged in to pistar but cannot get dashboard . Anonymoushttps://www.blogger.com/profile/13731724736187499031noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-69920186948280144892020-10-06T17:20:53.067-05:002020-10-06T17:20:53.067-05:00However I am now getting this error " unable ...However I am now getting this error " unable to read the firmware version after six attempts"<br />it then returns to the command line.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-47520387937786379752020-10-05T06:50:30.258-05:002020-10-05T06:50:30.258-05:00Forget the above because I am already logged in I ...Forget the above because I am already logged in I just needed to push enter at the pw prompt. Oh the joys of getting old!!Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-60014748061346545372020-10-05T06:11:04.234-05:002020-10-05T06:11:04.234-05:00When I access the ssh panel it and try and login i...When I access the ssh panel it and try and login i can input pi-star no problem but cannot input the password no characters or anything show on the screen. It is has if my keyboard has failed there is no input at all.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-47549492705875550062020-09-30T14:11:04.297-05:002020-09-30T14:11:04.297-05:00Before I found out what the mini-usb jacks were fo...Before I found out what the mini-usb jacks were for, I connected a charger via USB mini to the data port (they're identical..). I can't get this do do anything but flash solid green, slow red flash on the LEDs. Have I completely wrecked the thing? If so, can I salvage it, or do I have to replace it?<br /><br />Despite twice having entered my wifi SSID and password on the micro SD, it won't connect. If I get a new micro SD and flash the latest pi-star software onto it, adding my supplicant file, is there any hope that it will work?<br /><br />Thanks.<br /><br />jim K9JEC (living in an RF desert)<br /><br />Thanks.Jim Carroll, CRNAhttps://www.blogger.com/profile/00184804441302208917noreply@blogger.comtag:blogger.com,1999:blog-1755726614557851817.post-71821068322078748432020-07-18T12:05:00.967-05:002020-07-18T12:05:00.967-05:00This worked fine for me, as I couldn't get my ...This worked fine for me, as I couldn't get my MD-9600 to work on DMR, and running MMDVMCAL, the "difference" showed as 300, but DMR still didn't work for me, using an offset of300 for both RX and TXOFFSET, but after running, "BER," that resulted in a high, well, I felt that it was high anyway, RXOFFSET of about 950, and now my MD-9600 works just fine on DMR.Bernard Jarihttps://www.blogger.com/profile/16634403493600940996noreply@blogger.com